|
Aquila Rig #4 OIME PARCO S/L 7
(Working in
East Texas / Louisiana)
MAST &
SUB:
ONE (1)
PARCO SL-7 136’, 750,000 LB STATIC HOOK LOAD MAST, RACKING
BOARD & 5 SHEAVE CROWN BLOCK, FASTLINE SHEAVE, STANDPIPE AND
BOOM POLES
PARCO 21’
SPLIT LEVEL (17’ ROTARY CLEARANCE) SUBSTRUCTURE, V-DOOR,
STAIRS, HANDRAILS, WITH NATIONAL TYPE D WIRELINE ANCHOR.
8’W X 9’H X
37’L TOP DOGHOUSE, DRILLER LOCKERS, STORAGE BOXES, KNOWLEDGE
BOX, 2 DOORS
18”H X 9’W
X 60’L CATWALK WITH (10) 18”H PIPE RACKS AND (2) 42”H X 28’L
TRIANGULAR PIPE RACKS
DRAWWORKS:
ONE (1)
OIME (PARCO) SL-7 SINGLE DRUM DRAWWORKS, 1-1/4” LEBUS
GROOVED DRUM WITH TWO (2) GENERAL ELECTRIC DC TRACTION
MOTORS MOD. 5GE-752AU, 1000 HP EACH, AND PARMAC 342
HYDROMATIC BRAKE, OIME CW SL-7, FOSTER MAKE-UP AND BREAK-OUT
CATHEADS
ROTARY:
ONE (1)
NATIONAL C 275, 27-1/2” X 53-1/4” ROTARY TABLE WITH MASTER
BUSHING, INDEPENDENT DRIVE WITH ONE (1) GENERAL ELECTRIC
5GE-752AU, 1,000 HP DC TRACTION MOTOR
HOOK &
BLOCK:
ONE (1) BJ
400 TON BIG SHORTY BLOCK, WITH BECKETED HOOK WITH (6) 1-1/4”
X 50” SHEAVES
CROWN:
ONE (1)
PARCO CROWN WITH 7 - 50” – 1-1/4” SHEAVES
SWIVEL:
ONE (1)
EMSCO MODEL 400 TON SWIVEL.
TRIPLEX
MUD PUMPS:
TWO (2)
NATIONAL 10-P130, 1,300 HP TRIPLEX PUMPS WITH TWO (2)
GENERAL ELECTRIC DC TRACTION MOTORS MOD. GE-752AU, 1000 HP
EACH, INCLUDING HYDRIL MODEL K-20, 5,000 PSI PULSATION
DAMPERNERS, ONE (1) 6” X 5” CENTRIFUGAL SUPERCHARGER PUMP,
AND ONE (1) RELIEF SAFETY VALVE, SKIDDED.
GENERATORS DIESEL / AC:
THREE (3)
CATERPILLAR 3512T, 12 CYLINDERS 1,200 HP ENGINES WITH THREE
(3) 1050 KW KATO GENERATORS ON 10’W X 10’H X 30’L OILFIELD
SKID WITH ROOF.
TWO (2)
SULLIVAN PALATEK MODEL 30DG AIR COMPRESSORS WITH 30 HP
ELECTRIC MOTORS, RADIATORS, HORIZONTAL RECEIVER TANKS
MOUNTED ON SKIDS ONE AND TWO AND ONE (1)
Quincy cold start
compressor, diesel powered, MOUNTED ON SKID THREE.
SCR:
ONE (1) SCR
HOUSE, ROSS HILL, MOD. 1650 WITH 4 BAYS, 600 VOLTS, 1500 KVA.
WITH
CUTLER-HAMMER FREEDOM SERIES 2100 MOTOR CONTROL CENTER
480VAC, 60
HZ UNIT MOUNTED IN 10’W X 9’H X 20’L TEMPERATURE CONTROLLED
HOUSE ON OILFIELD SKID WITH TWO (2) TRANE AIR CONDITIONING
UNITS.
FUEL
TANKS:
ONE (1)
CYLINDRICAL, HORIZONTAL 10,000 GALLON FUEL TANK WITH
LUBRICATION TANK, OILFIELD SKID MOUNTED WITH FUEL FILTRATION
SYSTEM AND TWO (2) 1” FUEL TRANSFER PUMPS WITH 1-1/2 HP
MOTORS.
WATER
TANKS:
ONE (1) 400
BBL HORIZONTAL OPEN TOP WATER TANK, OILFIELD SKID MOUNTED
WITH TWO (2) 3” X 2” CENTRIFUGAL PUMPS POWERED BY 15 HP
MOTORS.
ONE (1) 250
BBL HORIZONTAL OPEN TOP WATER TANK, OILFIELD SKID MOUNTED
WITH PIPING
MUD
SHAKER TANK:
ONE (1) MUD
SHAKER TANK, 625 BBL, 8’W X 8’H X 52’L FLAT BOTTOM, THREE
(3) COMPARTMENT TANK WITH TWO (2) 6” X 5” MISSION
CENTRIFUGAL PUMPS WITH 50 HP ELECTRIC MOTORS, AND ONE (1)
PETRO EQUIPMENT 7.5 HP MUD AGITATOR, OILFIELD SKID MOUNTED.
MUD TRIP
TANK:
ONE (1) 8’W
X 8’H X 10’L, 112 BBL, FLAT BOTTOM TRIP TANK WITH 8’L PORCH
WITH (2) 4” X 3” MUD HOG CENTRIFUGAL PUMPS WITH 30 HP
MOTORS, MUD JETS, SIDE OBSERVATION PLATFORM ON OILFIELD SKID
MUD
SUCTION TANK:
ONE (1) MUD
SUCTION TANK, 480 BBL, 8’W X 8’H X 52’L FLAT BOTTOM, THREE
(3) COMPARTMENT TANK AND 10’L COVERED PORCH WITH TWO (2) 6”
X 5” MISSION CENTRIFUGAL PUMPS WITH 50 HP ELECTRIC MOTORS,
THREE (3) PETRO EQUIPMENT 7.5 HP MUD AGITATORS AND TWO (2)
MUD HOPPERS, OILFIELD SKID MOUNTED.
DESILTER
/ DESANDER / SHAKER:
ONE (1)
SWACO CONE DESILTER WITH 16-4” CONES
ONE (1)
SWACO CONE DESANDER WITH 2-12” CONES
TWO (2)
SWACO MONGOOSE DUEL MOTION LINEAR SHALE SHAKERS
BLOW OUT
PREVENTION EQUIPMENT:
ONE (1)
CAMERON CLOSING UNIT, 6-STATION, 160 GAL CAPACITY, WITH 2
AIR PUMPS, TRIPLEX HYDRAULIC PUMPS WITH 20 HP ELECTRIC
MOTOR, SKIDDED WITH 4-STATION REMOTE CLOSING UNIT LOCATED ON
THE DOG HOUSE.
ONE (1)
CAMERON 11” X 10,000# ANNULAR PREVENTER
ONE (1)
CAMERON 11” X 10,000# DOUBLE RAM PREVENTER
ONE (1)
CAMERON 11” X 10,000# SINGLE RAM PREVENTER
ONE (1)
10,000# CAMERON CHOKE MANIFOLD, 8’6”W X 17’0”L, SKIDDED
AUXILIARY EQUIPMENT:
A)
AUTOMATIC DRILLER
B) (20) 6”
DRILL COLLARS
C) KELLY:
5-1/4” HEX X 42’
D) KELLY
SPINNER
E) PIPE
SPINNER
F) TWO (2)
INGERSOL 10,000# AIR HOISTS
G) ROTARY
TONGS, ELEVATORS, HANDLING TOOLS
H) PARTS
HOSE, 10’W X 8’H X 18’L
I) (14)
RIG MATS, STEEL FRAME
J)
SUITCASES
K) PATSO
WIRELINE UNIT
L) TOOL
PUSHER QUARTERS AND 12-MAN CREW QUARTERS
|
